Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] AM623: 4GB LPDDR4

    Part Number: AM623 Tool/software: Hi team, A customer wants to have 4GB LPDDR4 (single channel topology). They could not find 4GB 16-bit single-channel LPDDR4, there is only 2GB option. Can they use a 32-bit device and only connect one channel?…

  • [FAQ] AM62P: How to measure wakeup latency for Low Power Modes on AM62x/A/P

    Part Number: AM62P Tool/software: How can you measure the wakeup latency for Low Power Modes on AM62x/A/P? Low Power Mode's wakeup latency is the amount of time required from triggering a wakeup event to resuming normal operation. This FAQ shows to…

  • [FAQ] AM62x, AM62Ax, AM62D-Q1, AM62L, AM62Px, AM64x, AM243x, Custom board hardware design – How to handle Used / Unused Pins / Peripherals and add pullup or pulldown? (e.g. GPIOs, SERDES, USB, CSI, MMC (eMMC, SD-card), CSI, OLDI, DSI, CAP_VDDSx, .......

    Part Number: AM625 Tool/software: Hi TI Experts, Is there any application note with information about how to connect IOs or Peripherals - Used or Unused Details on the connections to be done when used. When not used, should these IOs or Peripherals…

  • [FAQ] TDA4VH-Q1: How to change the ATF to print on MCU_UART in SBL bootflow

    Part Number: TDA4VH-Q1 Tool/software: In the SBL bootflow, using BootApp, how to print ATF logs on MCU_UART or WKUP_UART?

  • [FAQ] How to enable switching capability between GPO and GPI operation for PRU GPIO?

    Part Number: AM6442 Other Parts Discussed in Thread: SYSCONFIG Tool/software: Each PRU_ICSSG PRU processor implements fast GPO through its R30 register and fast GPI through R31 register. AM64x/AM243x has 20 pinned out PRU GPIO pins and the device…

  • [FAQ] AM625: ETH1_LED_100 and ETH1_LED_ACT dose not work

    Part Number: AM625 Tool/software: Hello IT Expert Our custom board uses the same reference design of Ethernet/LED HW as in attached custom board schematic. 1. There is no signal (100%) for CPSW_ETH1_LED_ACT (even we make network traffic by ping…

  • [FAQ] AM3351 , AM3352 , AM3354 , AM3356 , AM3357 , AM3358 , AM3359 Custom board design – E2E and FAQ references to Get started

    Part Number: AM3352 Other Parts Discussed in Thread: AM3358 , AM3354 , AM3359 , , AM3356 , SYSCONFIG Tool/software: Hi TI Experts, Can you provide a List of E2Es that can be referred when starting a custom board hardware design?

  • [FAQ] How to read SOC_UID from OPTEE on AM6x SoC

    Part Number: AM625 Tool/software: SOC_UID is a device specific identifier calculated by ROM based on "KEK of the device which is unique to every single device, plus other ROM mata-data structure". - unique per SoC and persistent - available on HS…

  • [FAQ] AM625: DVH Trace Length Matching Requirements

    Part Number: AM625 Tool/software: Hi, I'm designing a DVH to be laid out by SVT and am working on the layout guidelines for them. I am trying to find the trace length matching requirements for certain components but can't seem to find them on any…

  • [FAQ] SK-AM62B-P1: How to implement encrypted filesystems using dm-crypt and initramfs

    Part Number: SK-AM62B-P1 Tool/software: Hello all, This is a detailed guide on implementing an encrypted filesystem on an SK-AM62B-P1 using dm-crypt. Please note that similar steps with minimal changes should also work on other targets based on…

View FAQ threads
  • Threads 198526 Discussions