Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TMS320C6678: Quick set up Guide C6678 and C6678-EVM

    Part Number: TMS320C6678 Other Parts Discussed in Thread: CCSTUDIO Hi, Would you please provide a " Quick set up Guide or development guide or start up guide for C6678 and C6678-EVM " to enable a quick product development ?

  • [FAQ] TMS320C6678: How to generate the CCS PDK examples for C6678?

    Part Number: TMS320C6678 Hi, I would like to know the list of examples available for C6678. In the processor SDK, the steps to create CCS PDK examples for C6678 are more generic for the series of processors. Please provide the steps, particularly…

  • [FAQ] TMS320C6678: How to re-build the PDK and SDK of PROCESSOR-SDK-C667X 6.3 for C6678?

    Part Number: TMS320C6678 Other Parts Discussed in Thread: PROCESSOR-SDK-C667X Hi, How to re-build the PDK and SDK of PROCESSOR-SDK-C667X 6.3 for C6678?

  • [FAQ] TMS320C6657: Quick start Guide C6657 and C6657-EVM

    Part Number: TMS320C6657 Other Parts Discussed in Thread: CCSTUDIO Hi, Would you please provide a " Quick start Guide C6657 and C6657-EVM " to enable a quick product development ?

  • [FAQ] AM6442: question about MCU_OSC0 Start-up

    Part Number: AM6442 Team, I have a question about "Figure 7-16. MCU_OSC0 Start-up Time" from the datasheet. Here it looks like that MCU_OSC0 is only allowed to start when VDD_MCU is ramping. In reality the osciallation starts already with VDDS_OSC0…

  • [FAQ] AM62x: CLKOUT0 for RMII_50MHz_CLK and PHY_REFCLK connection

    In below diagram, CLKOUT0 to drive 4 terminal need external buffer. If CLKOUT0 only drive 2 terminal, can it just connected together or with resistors like below.

  • [FAQ] [TDA4VL] The board can't display by DP port

    Other Parts Discussed in Thread: TDA4VL Hi experts, Using TDA4VL board and 8.0.3 SDK, build and make SD card by default setting, it boot normally but don't display by DP port, and can't get any info about display driver by command: modetest -M tidss…

  • [FAQ] TDA4VM: How to build SBL in debug mode j721e RTOS SDK?

    Part Number: TDA4VM Hi, I am trying to build SBL in debug mode using BUILD_PROFILE=debug flag, but the build fails with the error “gmake: *** No rule to make target 'sbl_mmcsd_img'. Stop.”. Is there a way to build SBL in debug mode?

  • [FAQ] TDA4VM: NEON Support in PSDK QNX

    Part Number: TDA4VM As per the TDA4VM TRM, the ARM Corext-A72 Subsystem used by the TDA4VM supports " Advanced Single Instruction Multiple Data (SIMD) and floating point extension (Arm Neon ) ". Please refer to this page that points to the ARM Architecture…

  • [FAQ] TDA4VM: Query regarding CPSW9 MAC port mapping with PHYs

    Part Number: TDA4VM Hi All, The 8 ports on J721E is divided like this RGMII Ports - 1,3,4,8. QSGMII ports - 2,5,6,7 1. The CPSW mac ports is mapped sequentially with PHY. MAC0->RGMII port1, MAC1->RGMII port3 and so on. Am I correct? 2. If…

View FAQ threads
  • Threads 197956 Discussions