Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] Transceiver FAQs

    Click the links below to navigate to the respective interface FAQs. CAN FAQs I2C/I3C FAQs RS-485 RS-422 RS-232 FAQs LIN FAQs

  • [FAQ] TUSB2E22: Is there an eUSB2 repeater in a QFN package?

    Part Number: TUSB2E22 The TUSB2E22, TI's dual eUSB2 to USB repeater, is currently shipping in a small form factor BGA, but what if your application requires an easier to assemble QFN package?

  • [FAQ] TUSB8041: How do I test USB 3.0 / USB 3.1 / USB 3.2 Electrical Compliance on USB Hubs?

    Part Number: TUSB8041 Other Parts Discussed in Thread: TUSB8040 , , TUSB8020B , TUSB8042 , TUSB8042A USB 3.0 / 3.1 / 3.2 SuperSpeed 5 Gbps electrical compliance testing requires an oscilloscope and BERT from an approved vendor, as well as dedicated SuperSpeed…

  • [FAQ] DS90UB941AS-Q1: Access Two Deserializers in Splitter Mode which have the same I2C Address

    Part Number: DS90UB941AS-Q1 When DS90UB941AS-Q1 is connected to two remote deserializers in splitter or independent mode which have the same physical I2C address, how can they be accessed independently via I2C?

  • [FAQ] DS90UB962-Q1: Using Software to identify if deseralizer is 960 or 962

    Part Number: DS90UB962-Q1 Hi Team, I have a build that mixes 960s and 962s due to shortages. One of my cameras that connects to the build needs to dynamically reduce the FPS if it is connected to a 962 because the 3gbps link leads to bandwidth limitations…

  • [FAQ] DS90UB947-Q1: MAPSEL question

    Part Number: DS90UB947-Q1 Hi team My customer Hasco is using our 947 and configure its mode_sel1, here is our question: 1. When our VR6=0V, the 0x4F read back value is 0x40 which means the bit[7] is 0 and that is described to be the SPWG mapping…

  • [FAQ] DS90UB954-Q1: PDB Hard Reset Required?

    Part Number: DS90UB954-Q1 In the 954 datasheet the Power Up Sequencing figures 55 and 56 show a hard reset after the first PDB. Is this a requirement, recommendation, or only there to show if you do a hard reset after power up the required timing(t7…

  • [FAQ] TPD1E01B04-Q1: How do you correlate capacitance needed in ESD protection device with protocol data rate?

    Part Number: TPD1E01B04-Q1 Other Parts Discussed in Thread: ESD401 , TPD1E10B06 , Hi Erika, Could you help to recommend the ESD diode for the UB933 and UB954? What’s the maximum IO cap for the FPD-link for these two parts? Customer want to know…

  • [FAQ] DS90UB941AS-Q1: Recommendation of 941AS external oscillator for splitter mode

    Part Number: DS90UB941AS-Q1 Other Parts Discussed in Thread: CDCE937-Q1 , CDCE913-Q1 Hi team I would like to ask a question about recommendation of 941AS external oscillator for splitter mode. Customer system is one 941AS with two 948 using splitter…

  • [FAQ] TVS2700: Surge package alternatives

    Part Number: TVS2700 Other Parts Discussed in Thread: FLAT-CLAMP-TVS-EVM One of my customers was recently looking for TVS diodes to protect their system from surge events, and they came across TI's TVS flat-clamp devices, particularly the TVS2700. They…

View FAQ threads