• Threads 48905 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TMS570LC4357: Examples and Demos available for Hercules Controllers (E.g. TMS570x, RM57x and RM46x etc)

    Part Number: TMS570LC4357 Other Parts Discussed in Thread: HALCOGEN , MOTORWARE , TMS570LS3137 , , DRV8301 I am listing out all the available examples and demos available on Hercules Controllers (E.g. TMS570x, RM57x and RM46x etc) as per my knowledge…

  • [FAQ] AM2634: How to set SPI baudrate in EB Tresos

    Part Number: AM2634 Hi, Experts. As title description, this setting should be appear in "SPIExternalDevice" tab, but I do not find this setting. I found MCAL driver documents writes as below. My question is : How to set fSPI frequency…

  • [FAQ] MCU-PLUS-SDK-AM243X: [FAQ] Can you provide the list of FAQs for AM24x devices ?

    Part Number: MCU-PLUS-SDK-AM243X Provide the list of FAQs for AM24x devices segregated domain-wise ?

  • [FAQ] RM57L843: Describing step by step procedure to use Ethernet Bootloader in static IP for Hercules device (RM57x)

    Part Number: RM57L843 Describing process to download the application binary to the RM57x Hercules controller using Ethernet Bootloader in Static IP mode.

  • [FAQ] TMS570LC4357: How to download HET IDE

    Part Number: TMS570LC4357 While downloading HET IDE from below link HET_IDE IDE, configuration, compiler or debugger | TI.com Getting "Service Unavailable" error

  • [FAQ] RM48L952: How to perform 8 Byte transfer in SCI Multi-buffered Mode using DMA

    Part Number: RM48L952 When i was writing multi-buffered SCI using DMA in SCI2 Driver. However, my code was able to transmit up to 4 bytes, but when I tried to transmit 8 bytes, the RM48L952 stopped working. Even if I check the datasheet, it seems that…

  • [FAQ] MCU-PLUS-SDK-AM243X: How to use Tune PHY with MCU_PLUS_SDK for OSPI Controller ?

    Part Number: MCU-PLUS-SDK-AM243X Q1. How to tune PHY with MCU_PLUS_SDK ? Q2. Why is PHY tuning required ?

  • [FAQ] AM2634: How to configure Watchdog (WDG) in MCAL?

    Part Number: AM2634 I am currently using MCAL version X.Y.Z how do I configure the WatchDog peripheral to a desired expiry time i.e., After time " t ", the WDG must expire and issue a POR reset if not serviced.

  • [FAQ] MCU-PLUS-SDK-AM263X: How to implement streaming or scatter gather mode for DTHE-AES ?

    Part Number: MCU-PLUS-SDK-AM263X Q1. How to optimize the DTHE-AES engine usage to support multiple algorithm in parallel or support to use it by-parts ? Q2. How to optimize the memory usage by reusing the same region for authentication ? Q3. What…

  • [FAQ] MCU-PLUS-SDK-AM263X: [FAQ] Can you provide the list of FAQs for AM26x devices ?

    Part Number: MCU-PLUS-SDK-AM263X Provide the list of FAQs for AM26x devices segregated domain-wise ?

View FAQ threads