• Threads 52549 Discussions
Texas Instruments (TI) Microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search for content on other microcontrollers or ask technical support questions on the extensive portfolio of microcontrollers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] MSPM0-SDK: Important note for early MSPM0 customers

    Part Number: MSPM0-SDK Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH , Important note for early MSPM0 customers TI recently launched a new family of Arm Cortex-M0+ MCUs , including the MSPM0L series and MSPM0G series . These MCUs are accompanied…

  • [FAQ] AM2434: [AM243x/AM64x] Is there a Unique Identifier somewhere in the register map?

    Part Number: AM2434 Hi, I'm looking at enabling in the field provisioning (also factory provisioning) of devices that are using the AM243x/AM64x family of Sitara products. I would like to be able to uniquely identify each module and was hoping the…

  • [FAQ] AM2x: FreeRTOS Multiprocessing?

    Part Number: LP-AM243 Hi experts, I am evaluating AM243x with MCU+SDK 8.5.0.24. I noticed in the FreeRTOS docs that FreeRTOS has a multiprocessing feature called SMP , which would be an interesting option for AM243x. Is this feature included in…

  • [FAQ] AM2634: [FAQ] How to debug TIFS-MCU for Cortex M4 on am263x/am273x ?

    Part Number: AM2634 Q1. How to debug TIFS-MCU on Cortex M4 in HS-FS devices ? Q2. How to debug TIFS-MCU on Cortex M4 in HS-SE devices ? Q3. In HS-SE devices, is there a way to leverage the flow to open the debug for HSM M4 in development environment…

  • [FAQ] MCU-PLUS-SDK-AM263X: How to configure CPSW 2G ALE to add static entries ?

    Part Number: MCU-PLUS-SDK-AM263X Hi Experts, How do I configure CPSW 2G ALE to filter packets based on VLAN, Ethernet Type, Source MAC, Destination MAC, IP address etc?

  • [FAQ] MCU-PLUS-SDK-AM263X: Configuring GPIO Interrupts

    Part Number: MCU-PLUS-SDK-AM263X Other Parts Discussed in Thread: SYSCONFIG Hi How to Configure GPIO Interrupts in AM263x for individual GPIO pins. How is it different from the existing GPIO Bank Interrupt Configuration example in the SDK.

  • [FAQ] Sitara MCU EVM and LaunchPad Power Supply Requirements

    Other Parts Discussed in Thread: TMDSCNCD263 , TMDS243EVM , LP-AM263 , LP-AM243 , TUSB320 The following FAQ applies to AM243x LaunchPad (LP-AM243), AM263x LaunchPad (LP-AM263), AM243x General Purpose Evaluation Module (TMDS243GPEVM, TMDS243EVM), AM263x…

  • [FAQ] MCU-PLUS-SDK-AM243X: How to identify if the device is GP device or HS device ?

    Part Number: MCU-PLUS-SDK-AM243X How to identify which image should I use ? Should I use *.hs_fs.tiimage or *.tiimage for SBL programing on my device. Does it matter ? Does it affect any of my application ?

  • [FAQ] MCU-PLUS-SDK-AM263X: Important SBL Links

    Part Number: MCU-PLUS-SDK-AM263X Other Parts Discussed in Thread: UNIFLASH [AM263-SBL] Where can I find information of getting started with the AM263 SBL, Bootflow and Booting Tools?

  • [FAQ] MCU-PLUS-SDK-AM243X: EtherCAT MainDevice with TI sitara devices(AM263Px/AM261x/AM243x/AM263x/)

    Part Number: MCU-PLUS-SDK-AM261X Hello Experts, I need to implement a standalone EtherCAT MDevice(MainDevice) on TI AM2x series MCU devices . My issue is where will i get a master stack to run on it? Also will there be some sample MDevice stack…

View FAQ threads