Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS90UB949-Q1: single mode question

    Part Number: DS90UB949-Q1 Dear team, 1. If the customer only uses single port, can they use port 1? 2. If the customer connect 949 to 948 and use dual link mode, is it ok to connect 949's port 0 to 948's port 1 and connect 949's port 1 to 948's…

  • [FAQ] TUSB8041: TUSB8041: How do I force a USB Hub to send USB 2.0 high speed test packets for eye diagram testing?

    Part Number: TUSB8041 Other Parts Discussed in Thread: TUSB8044A , , TUSB8020B , TUSB8042A , TUSB8044 , TUSB8042 , TUSB8043 , TUSB8040 , TUSB8043A USB 2.0 high speed signal quality (eye diagram) testing requires a USB port to send a USB 2.0 test packet…

  • [FAQ] What TI ESD/TVS diode should I use to protect Interfaces in my system?

    I have various interfaces in my system I would like to protect against system-level ESD, could you provide some recommendations for me including for USB, push-button, HDMI, Ethernet?

  • [FAQ] Analog video conversion and transport

    Other Parts Discussed in Thread: DS90UB933-Q1 , TVP5150AM1 , TVP5150 Hi, I would like to know if there is a IC that convert analog video (PAL/NTSC/..) to parallel 10/12 bit? Thanks Shmuel

  • [FAQ] DS90UB940-Q1: link error meaning

    Part Number: DS90UB940-Q1 Hi experts, 1. 940 has link error counter which can monitor link error number. Could you please help to explain what kind of error can be taken as a link error? Datasheet states clk0, clk1 and DCA are monitored for link errors…

  • [FAQ] DS90UB948-Q1: Does its OLDI output support VESA and JEIDA

    Part Number: DS90UB948-Q1 Hi team Customer would like to ask that does 948's OLDI output support VESA and JEIDA mode/standard/protocol? Thank you.

  • [FAQ] DS90UB913A-Q1: YUV 8 support when paired with 933

    Part Number: DS90UB913A-Q1 Hi Team, I just wanted to confirm that a 913/933 pair can be used for 8 bit YUV-8 data format. I figure we can just run in 10 bit mode and only connect DIN[0:7] and leave the rest open. Let me know if there there are…

  • [FAQ] TLIN1024-Q1: In-line programming of LIN devices

    Part Number: TLIN1024-Q1 Hello, Team, I am new to LIN transceiver and have a question on the data rate that TLIN device supports. I found the description in the datasheet that " The LIN receiver supports data rates up to 100 kbps for faster in-line…

  • [FAQ] DS90UB940-Q1EVM: Test issue

    Part Number: DS90UB940-Q1EVM Other Parts Discussed in Thread: DS90UH940N-Q1 When debugging the ds90ub940 chip, we encountered the following problems. Please help us: 1. Using ds90ub940 official development board and Ti analog launchpad software …

  • [FAQ] DP83869HM: DP83869 in Bridge Mode to connect two MACs

    Part Number: DP83869HM Please refer below thread for register configuration needed. https://e2e.ti.com/support/interface-group/interface/f/interface-forum/911770/dp83869hm-bridge-rgmii-to-sgmii-mac-to-mac-configuration/3385960?tisearch=e2e-sitesearch&keymatch…

View FAQ threads