Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS90UB971-Q1: How can I optimize my FPD-Link camera design for system level ESD immunity?

    Part Number: DS90UB971-Q1 Other Parts Discussed in Thread: DS90UB960-Q1 , DS90UB953-Q1 Tool/software: How can I optimize my FPD-Link ADAS design to achieve better performance in system level ESD immunity testing? When striking my system with ESD pulses…

  • [FAQ] DS280DF810: The new set of DS2x0DFx10 devices Version IDs do not match the Version IDs of previous set (Register 0xF0)

    Part Number: DS280DF810 Tool/software: In TI's DS2x0DFx10 Ethernet retimer devices, there is a Version ID register that can be used to read back the device version. For groups implementing this device, we frequently see them checking this Version ID to…

  • [FAQ] DS110DF111: Does TI's Ethernet Signal Conditioning Portfolio Support Base-T Ethernet?

    Part Number: DS110DF111 Tool/software: Texas Instruments has a wide range of signal conditioning devices for Ethernet. Sometimes we receive questions regarding a signal conditioning device's ability to support Base-T Ethernet. The majority of TI…

  • [FAQ] Measuring the maximum drive distance of a signal conditioner across a cable

    Part Number: TDP1204 Tool/software: Most redrivers and retimers advertise their equalization capabilities in dB but its difficult to quantify what that represents in terms of cable length. This FAQ is a guide to determine how long of a cable can be…

  • [FAQ] Why TUSB804x hub can not be detected in SMBUS mode

    Part Number: TUSB8042A Tool/software: When the SMBus interface mode is enabled, the TUSB804x supports read block and write block protocols as a receiver-only SMBus device. The TUSB804x will wait indefinitely for configuration by the SMBus host and will…

  • [FAQ] TUSB8041A: what is difference between I2C mode and SMBUS mode for TUSB80xx hub

    Part Number: TUSB8041A Tool/software: In I2C mode, Hub is master and I2C is used to read / write external EEPROM . Hub configuration can be changed by reading external EEPROM In SMBUS mode, hub is receiver, you can change hub configuration by changing…

  • [FAQ] DS320PR810: How should redriver thermal vias and solder paste patterns be designed?

    Part Number: DS320PR810 Other Parts Discussed in Thread: DS320PR410 Tool/software: Why do we need to consider thermal vias and solder paste for redrivers at the board layout stage, and how should they be handled?

  • [FAQ] LMH1229: Understanding Jitter Measurements

    Part Number: LMH1229 Tool/software: To understand the overall jitter measurement it is important to understand what jitter is. All system jitter measurements have components of Deterministic Jitter (DJ) and Random Jitter (RJ) that sum to make the Total…

  • [FAQ] TUSB211A: My USB2 Redriver is not boosting when enabled during testing.

    Part Number: TUSB211A Tool/software: I am enabling my TUSB211A while running test packets through our setup, but I am not seeing any boost. Why is that?

  • [FAQ] TMUXHS221: Alternate Signaling Mux Selection

    Part Number: TMUXHS221 Other Parts Discussed in Thread: TS3USB221E , , TS3USB3031 Tool/software: I want to mux signals with a range of bandwidths equal to or lower than USB3.0 data rates without getting a full USB3 mux. What would be the best mux for…

View FAQ threads