Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] What is PassFET Hang Time?

    Other Parts Discussed in Thread: TCA39306 FAQ: Logic and Voltage Translation > IxC >> What is PassFET Hangtime? To understand what passFET hangtime is, we need to define what a passFET is. A passFET is a transistor where the drain and source terminals…

  • [FAQ] TCAN1057A-Q1: why is the CAN Mosfet and Diode used

    Part Number: TCAN1057A-Q1 Tool/software: Hello experts！ I have a question about the purpose of the Mosfet and diode in CAN interface？ Further，How does CAN implement arbitration and error correction functions through hardware?

  • [FAQ] DP83822HF: How does power up sequence affect PHY operation?

    Part Number: DP83822HF Tool/software: For DP83822, there is a guidance where AVD and VDDIO must not exceed 0.3V prior to complete supply ramp, with an additional footnote suggesting AVD to ramp up after VDDIO to avoid false detection of VDDIO. False detection…

  • [FAQ] What is Stuck Bus Recovery?

    Other Parts Discussed in Thread: TCA4307 FAQ: Logic and Voltage Translation > IxC >> What is Stuck Bus Recovery? Stuck Bus Recovery is a mechanism built into an I2C device that automatically attempts to free the SDA bus during a stuck LOW condition…

  • [FAQ] What Makes an I2C Buffer Hot-Swappable?

    Other Parts Discussed in Thread: TCA9511A FAQ: Logic and Voltage Translation > IxC >> What Makes an I2C Buffer Hot-Swappable ? Hot-Swap also known as Hot-Plug means the unpowered device can be inserted into a live backplane without disruption of service…

  • [FAQ] DP83867E & DP83869HM: Expected Back-Powering on Power Supply Pins

    Part Number: DP83867E DP83869HM Other Parts Discussed in Thread: DP83869HM Tool/software: The following FAQ applies to the DP83869HM and all versions of the DP83867: E/IS/CS/IR/CR The Analog Supply pins (VDDA2P5 & VDDA1P8) power the MDI portion…

  • [FAQ] What Connections of I2C Buffers are not Allowed?

    Other Parts Discussed in Thread: TCA9617B , TCA9509 , TCA9801 , TCA9800 , TCA9803 , TCA9802 , TCA9511A , TCA4307 FAQ: Logic and Voltage Translation > IxC >> What Connections of I2C Buffers are not Allowed ? Part Numbers: TCA9517 , TCA9517A , TCA9509…

  • [FAQ] What are the different I2C Buffer Direction Control Mechanisms?

    Other Parts Discussed in Thread: TCA9517A , TCA9517 , TCA9511A , TCA4307 FAQ: Logic and Voltage Translation > IxC >> What are the different I2C Buffer Direction Control Mechanisms ? I2C buffers implement direction control mechanisms to determine which…

  • [FAQ] DP83822I: Does Oscillator Clock or other external clock source to XI pin need to be stable before PHY power?

    Part Number: DP83822I Tool/software: Yes, Clock in external clock mode shall be available at power ramp. If not available, it is recommended to hold RESET_N low and release it at least 100 us aer external clock is stable.

  • [FAQ] What is the "VILC" Electrical Spec in I2C Buffers?

    Other Parts Discussed in Thread: TCA9517A Part Numbers: TCA9517A , TCA9517 , TCA9509 FAQ: Logic and Voltage Translation > IxC >> What is the "VILC" Electrical Spec in I2C Buffers ? VILC = Input LOW Contention Voltage VILC is the internal voltage…

View FAQ threads