Texas Instruments (TI) Interface support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search interface IC content or ask technical support questions on everything from ESD protection to interfacing with USB, Ethernet, and HDMI. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] DS320PR810: How should PCIe signals be AC coupled?

    Part Number: DS320PR810 Other Parts Discussed in Thread: DS320PR1601 , DS160PR1601 Tool/software: How do I check to make sure my PCIe signals are AC-coupled correctly?

  • [FAQ] DP83TC812S-Q1: RGMII Shift and Align Mode

    Part Number: DP83TC812S-Q1 Tool/software: Hello, Here is a summary of available information about RGMII Shift and Align mode for our DP83TC81x devices: A minimum of 1ns setup and 1ns hold time must be maintained at the input of the receiver…

  • [FAQ] LMH1239: SDI Layout Suggestions

    Part Number: LMH1239 Other Parts Discussed in Thread: LMH1297 Tool/software: Hello SDI engineers and LMH enthusiasts, Figure 1 - 3:5 for SDI In this E2E FAQ, I will be discussing GND plane layout best practices for SDI designs. In cable driver…

  • [FAQ] TDP142: Linearity Range Description

    Part Number: TDP142 Other Parts Discussed in Thread: TDP2004 , , TDP1204 Tool/software: Hi Experts, What does 'Linear range' refer to on re-drivers like TDP142, TDP1204, TDP2004,...?

  • [FAQ] Device Mismarked with A5

    The device I received is marked as 'A5' but that is not listed as an option in the datasheet.

  • [FAQ] PC -> EVM 983 -> Display with 988 -> Display with 988 -> Display with 988

    Part Number: DS90UB988-Q1EVM Tool/software: Hello, Is it possible to use this setup to test the daisy chain feature with the following setup: PC -> EVM 983 -> Display with 988 -> Display with 988 -> Display with 988 ~ Franz

  • [FAQ] DP83TC812S-Q1: Why is DP83Txxxx not passing compliance?

    Part Number: DP83TC812S-Q1 Other Parts Discussed in Thread: DP83TC811 Tool/software: For all 1000Base-T1 and 100Base-T1 compliance tests (including Interopability/link-up, PMA, PHY Control, PCS, and EMC), there is a required software configuration to…

  • [FAQ] DP83848Q-Q1: How to Disable 25Mhz CLKOUT Output

    Part Number: DP83848Q-Q1 Tool/software: If the CLKOUT output is not used on DP83848, it may be disabled using the below register writes. This may be beneficial for EMC emissions testing, in order to minimize the energy of 25Mhz harmonics. 0x13[0] =…

  • [FAQ] DP83867E: What IPG intervals can this PHY support?

    Part Number: DP83867E Tool/software: DP83867 supports the expected 12 byte IPG at the MDI as well as lower amounts in some conditions. This number comes from IEEE802.3 section 4.4.2 which sets out that the minimum IPG for a transmitted frame is 12 bytes…

  • [FAQ] XIO2001: MicroStar BGA Discontinuation and New nFBGA Package Designators

    Part Number: XIO2001 Tool/software: Devices in the MicroStar Jr. BGA packaging were discontinued and redesigned using a laminate nFBGA package in 2020. This nFBGA package offers datasheet-equivalent electrical performance. It is also footprint equivalent…

View FAQ threads