Texas Instruments (TI) C2000™ microcontrollers support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search C2000™ microcontroller content or ask technical support questions on our families of real-time control MCUs. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TMS320F28P650DK: Ethercat Important Documentation.

    Part Number: TMS320F28P650DK Understanding Ethercat: Introduction to Ethercat by Beckhoff : EtherCAT Introduction ETG.2200 EtherCAT, EtherCAT P and Safety over EtherCAT Slave Implementation Guide Section I - Technology Register Description…

  • [FAQ] JTAGLOCK on F28004x

    Part Number: TMS320F280049C This thread addresses common issues encountered with the JTAGLOCK feature on F28004x MCUs.

  • [FAQ] Help, my F280033/F280034 device won't boot to flash!

    Part Number: TMS320F280033 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH The default boot to flash entry point is 0x80000 in the F28003x Boot ROM, which is not in the memory map for the F280033/F280034 subset parts. This thread will detail how…

  • [FAQ] C2000 Bootloading Design Considerations

    Other Parts Discussed in Thread: C2000WARE This thread will discuss the best practices for custom bootloading on the following devices: F2807x F2837xS F2837xD F28004x F2838x F28002x F28003x F280013x F280015x F28P65x F28P55x …

  • [FAQ] F29H850TU: CAN Module Configuration

    Part Number: F29H850TU Other Parts Discussed in Thread: SYSCONFIG Is there any document explaining CAN module configuration parameters and how to configure these parameters in Sysconfig tool?

  • [FAQ] TMS320F28P550SJ: ADC gain offset calibration

    Part Number: TMS320F28P550SJ Hello, I followed outlined steps in gain calibration section of TRM chapter, but for some reason my ADCRESULT register does not show 0.9 * VREFHI, but a floating value. What could be the reason?

  • [FAQ] TMS320F28P550SJ: F28P55x ADC zero offset calibration

    Part Number: TMS320F28P550SJ I had an issue with ADC Zero Offset calibration. I followed steps outlined in TRM, but for some reason my Vreflo ADCRESULTREG keeps showing zero instead of certain offset. Could you help me with this issue, please?

  • [FAQ] C2000Ware - Errata

    Other Parts Discussed in Thread: C2000WARE , SYSCONFIG This post is meant to specify erratas /document any refinements or clarifications discovered after the C2000Ware release. Sysconfig migration/Switch feature in Sysconfig 1.26 does not work with…

  • [FAQ] TMS320F2800137: How do I port E-Metrology library from F28P55 to another TI C28x MCU Device?

    Part Number: TMS320F2800137 Other Parts Discussed in Thread: C2000WARE Hello, I want to port the E-Metrology library fom F28P55 to F2800137. I want to enable only single-phase calculations and I do not wish to calculate THD. What steps can I follow…

  • [FAQ] TMS320F28P550SJ: Theory behind the calculation of the metrology parameters computed in the E-Metrology Library on F28P55 and F28P65

    Part Number: TMS320F28P550SJ Hello! Thank you for your interest in the E-Metrology Library for F28P55x and F28P65x. If you are interested in knowing more about how the metrology parameters are calculated and the mathematical formulae used to do please…

View FAQ threads